Skip to content
In Tasmania, this is called Vehicle Inspection
TAS

Mobile Vehicle Inspection in Tasmania

In Tasmania, this is officially called a Vehicle Inspection. Browse mobile providers across 769 suburbs in TAS. Tasmania requires inspection on transfer of ownership, re-registration, and after defect notices. Inspection report valid 14 days for transfer purposes.

Devonport7310Sandy Bay7005Glenorchy7010Kingston7050Howrah7018Claremont7011Blackmans Bay7052Riverside7250Ulverstone7315Newnham7248Lindisfarne7015New Town7008Wynyard7325West Hobart7000Lenah Valley7008New Norfolk7140Moonah7009Newstead7250South Hobart7004Prospect Vale7250South Launceston7249Trevallyn7250Bellerive7018George Town7253West Launceston7250West Ulverstone7315Latrobe7307Brighton7030Youngtown7249East Devonport7310

Top suburbs in TAS

TAS

Devonport

7310
TAS

Sandy Bay

7005
TAS

Glenorchy

7010
TAS

Kingston

7050
TAS

Howrah

7018
TAS

Claremont

7011
TAS

Blackmans Bay

7052
TAS

Riverside

7250
TAS

Ulverstone

7315
TAS

Newnham

7248
TAS

Lindisfarne

7015
TAS

New Town

7008

All suburbs in Tasmania

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

U

V

W

Y

Z

Tasmania Vehicle Inspection guide

Terminology, validity, fees, exemptions and government sources for Tasmania.

Read the TAS guide →

Before the inspector arrives

Tyres
Tread depth
Minimum legal tread is 1.5 mm across the central three-quarters of each tyre. Use a coin or tread gauge, if a 20-cent coin sits more than halfway in the groove, replace.
Pressure
Set to the placard pressure (usually inside the driver door jamb) when cold. Under-inflated tyres fail for sidewall flex and uneven wear; over-inflated fail for centre wear.
Sidewall condition
Check for bulges, cuts, cracks or exposed cords. Any sidewall damage is an automatic fail and a safety risk, replace before the inspection.
Lights
Headlights (low and high beam)
Both low and high beam must work on left and right. Aim should not be wildly off, a hazy, oxidised lens that cuts output also fails.
Tail lights
Both rear tail lights illuminate when the parking or headlights are on. Check for cracked lenses letting white light show rearward.
Brake lights
All three brake lights (left, right, high-mount) must light when the pedal is pressed. Get a helper to confirm, a dead bulb is the most common single fail.
Indicators
Front, side and rear indicators flash amber at the correct rate (60–120 per minute). Hazard switch must flash all four together.
Reverse lights
White reverse lights come on when reverse gear is selected with ignition on. Check both sides where fitted.
Number plate light
The white lamp over the rear plate must illuminate the entire plate at night. A blown bulb here trips a lot of inspections.
Brakes
Pedal feel
Pedal should be firm with no sponginess. It should not sink toward the floor when held under steady pressure with the engine running.
Parking brake
Hold the vehicle on a moderate slope. Lever or foot brake should engage within its rated travel and not release on its own.
Wipers and washers
Wiper blades
Blades clear the windscreen without streaking, juddering or smearing. Torn rubber is a common fail, blades are cheap to replace.
Washer jets
Both washer jets spray cleanly onto the windscreen. Empty bottle, blocked jet or split hose all fail.
Windscreen
Chips and cracks
No cracks longer than 30 mm or any damage in the driver wiper arc. Repair small chips with a windscreen kit before the inspection, replacements take days.
Suspension
Bounce test
Push down hard on each corner and release. The vehicle should rebound and settle within one or two oscillations. Excessive bounce indicates worn dampers.
Exhaust
Leaks and noise
No blowing sound from joints or holes, no excessive smoke, and noise level reasonable for the vehicle type. Black soot around joints is a leak indicator.
Seatbelts
All belts retract and lock
Every fitted belt must extend smoothly, retract under tension, and lock instantly when jerked. Frayed webbing or a sluggish retractor will fail.
Mirrors
Interior and both exterior
All three mirrors fitted, secure, and free of cracks. Power mirrors must adjust on both axes if originally fitted.
Horn
Horn operates
Horn sounds clearly from a single button press. A weak or intermittent horn fails.
Bodywork
Rust
Structural rust, sills, chassis rails, mounting points, suspension towers, is an automatic fail. Surface rust on panels is usually fine.
Sharp edges and panels
No torn metal, hanging trim or sharp protrusions that could injure pedestrians. Loose bumpers or dragging plastic must be secured.
Fluids
Engine oil
Check on level ground with a warm engine. Level between MIN and MAX, no milky contamination, no major leaks evident under the car.
Coolant
Coolant in the overflow bottle between MIN and MAX with the engine cold. No oily film and no obvious leaks at hoses or radiator.
Brake fluid
Reservoir between MIN and MAX. Fluid that is dark brown indicates age, flush before inspection if it is years old.
Number plates
Legible and securely fitted
Both plates fitted in the original mount points, all characters legible, no missing fasteners or cable-tied plates. A faded plate fails.
TAS-specific checks
Vehicle Inspection: validity timing
In Tasmania a Vehicle Inspection is valid for 14 days from issue. Time the inspection close to the sale or registration date so it does not expire before transfer.
Fee expectation
Typical mobile inspection fee for a car in Tasmania is $80–$140. Quotes well below the low end usually exclude travel; quotes above the high end usually include same-day or after-hours premium.